Plastic Fantastic 2

SuperBuickGuy · Oct 8, 2018

time to clear the space

I'll need to build new structure to support the fiberglass... but there is space

roughly in place.... it needs to move up 2 1/2"

of course, that means removing the cross member

tomorrow I'll build support structure for the frame - most likely that means building some kind of front roll cage then attaching the body to it...edited

SuperBuickGuy · Oct 9, 2018

So more workedited
notice how the pivot and the ball joint are on different planes?edited

though the Russian judge will never give more score for it, the C5 has a different spindle height and different pivot plane

so let's eyeball the problem.edited the ball joint is about in the same place as the C3 pivot would be..... only difference is the center of the hub is 20" away from the fender vs. the 16 or so that's stockedited

so time to move the frame into the frame

first cuts

chopped

time to weld a brace in place

chopped again

now things can move up

and it needs to move back a bit

Red77 · Oct 10, 2018

I'm really enjoying living vicariously through your experience here. Keep the updates coming!

SuperBuickGuy · Oct 12, 2018

so to more detail.
last night I got it more centered - look at the front, bumper bolt hole

warning if anyone is copying this - those holes are not, exactly in the same spot on either side

another tip - the front control arm hole is 3/4" lower then the rear hole.... this picture is close to where it needs to live
Use the hole where the lines are drawn (rear) - those holes are supposed to be in the same spot on either side.edited That said, trust but verify.

SuperBuickGuy · Oct 15, 2018

so more fitting.... I think (hope) it'll be okay to move it up 1 1/2"edited .... I still need to get a legible copy of the suspension points on a C5;

originally, my calculations showed it here

but I talked myself out of it.... we will see, I'll mock it together before I do any more cutting to doubly verify where the wheel will end (vertically) in the wheel well.edited Even if this is a bit further from the ground the 1/2" at the ball joint won't make much, if any, handling difference.
The other thing... I'm going to eventually cut the stubs off in front of the motor mount and use new metal...edited

Red77 · Oct 15, 2018

I guess you could completely clean up that area, you won't be needing the spring pockets anymore. Good to have for now as you are still trying to verify the right position in relation to what was there before, but is is an unnecessary chunk of weight and complexity once you have it figured out. Are you planning on fishplating in some rectangular tube stubs for the subframe pickup points?

SuperBuickGuy · Oct 16, 2018

Red77 said:
I guess you could completely clean up that area, you won't be needing the spring pockets anymore. Good to have for now as you are still trying to verify the right position in relation to what was there before, but is is an unnecessary chunk of weight and complexity once you have it figured out. Are you planning on fishplating in some rectangular tube stubs for the subframe pickup points?

motor mounts are behind the pockets. I have 4x4 3/16 wall tube, but also I'm close to ready to use my plasma table so if those stars align, we will see.

my current spring plan is use a coil-over-conversion for a C5 so the pockets are not only unnecessary but in the way.... that said, it's a whole lot easier to line things up with the frame in there.

I also plan on removing the frame above the Camaro rear assembly - it's unnecessary too. The body is going to come off enough to clean all of that up, then back together for shakedown, then apart for beautification.... likely this next summer will be the shakedown and the body in black primer.... or red, or grey or whatever is on the shelf...

Red77 · Oct 16, 2018

Sounds like a good plan. Without a frame table to work with, I think you probably have gone about this in the best way possible to maintain good dimensional references. It might be more work, but it will be right when it is all said and done. My cousin bought a huge table years ago for frame building. I think it was probably a bed for a large traveling column or gantry style mill. It was roughly 10'X20' and a super heavy casting. It had T-slots in it for work holding, several drilled and tapped holes, etc. He got it for pennies on the dollar as a shop was closing down in Houston and basically paid for the rigging to get it out of the shop it was in. It made full chassis builds much easier, but very few of us have that luxury. He was in the right place at the right time.

SuperBuickGuy · Oct 16, 2018

I have the bits to make a frame table, but after doing one for the Fiat Spider, I just didn't find it was worth the hassle. Granted, if I was doing this for a business, a table would make this happen a lot faster - but my space is limited so it'd probably cost me more time because it's in the way then it would save.

that said, I love those 'must get them out now' deals - it's how I got my lathe.

so a brief note on course a course change

Originally, it was flares and 427. That remains the same, as most who follow know, I love my manual-everything C3s. However, with wide tires, 14" brakes along with a power rack (which I could simply short-circuit), I'm going to add hydraboost to the brakes and plumb the rack and then EFI on the 427. Likely I'll use a throttle-body based system (like FI tech). The reason for EFI is there is a possibility this car is going to get pitted against a C3 with a SBC 427 Corvette and a C3 with a LS 427 - both of which are going to be EFI cars, both of which have updated suspensions.... don't hold your breath for this, though, all of the cars have 2 year min. completion dates....

SuperBuickGuy · Oct 17, 2018

Today, I got a chance to get some good measurements off a C5 Corvette
what surprised me was that the cradle is 5 3/4 inches off the ground.... as of yesterday, it was 8

255 tire, now 7 1/4 off the ground

that is about right sitting in the car, yes, it looks low but I could put a 275/20 tire under it ...

time to make it permanent

the oil pan is actually above the cradle and the cradle is basically flat to the center cross member (meaning I can do a belly pan pretty easiliy

looking from the back

and again the front

next up is the front mount which will include the upper control arm mount.they are 13 inches above the lower control arm in the back 9 1/2 in the front..... basically as the tire goes up the upper arm is moving backward while the lower is going forward- but at different rates.... how the GM engineers figured all this out is pretty fascinating to me, hope it works with the Camaro rear

Red77 · Oct 17, 2018

It is fascinating, that's how they work in all the anti-dive, increased Ackermann, etc. When you look at some of the aftermarket front clips that are on the market, you rarely see any of this genius. I would imagine that shows in the handling or lack thereof. Probably not a big deal when you are upgrading a solid axle buggy suspension, but you are upgrading a Corvette here. Taking advantage of the advances in technology over the last 40 years is just good practice. This is going to be a fun ride.

SuperBuickGuy · Oct 17, 2018

Red77 said:
It is fascinating, that's how they work in all the anti-dive, increased Ackermann, etc. When you look at some of the aftermarket front clips that are on the market, you rarely see any of this genius. I would imagine that shows in the handling or lack thereof. Probably not a big deal when you are upgrading a solid axle buggy suspension, but you are upgrading a Corvette here. Taking advantage of the advances in technology over the last 40 years is just good practice. This is going to be a fun ride.

My generation went from "never use stock setups" to "use stock setups"... here's my prediction - I blog this, someone out there does a TV show coughcoughaaronkaufmancoughcough then someone else sells a 'new kit' that 'takes advantage of manufacturer engineering' ... again. Thankfully, so far, I haven't had someone who copied come back and try to 'splain' it back to me...

It's fine, though, I think making hotrodding more accessible is always the right answer - and some people don't have the skill or time to piece it together themselves. The whole point of my blogging my builds is a detailed record of what I did and how - whether it's by cash or by knowledge, if someone else gains from it.... that's cool by me. I have a day job that pays far better then what I'd get paid breathing bondo in someone else's shop.

rtj · Oct 17, 2018

Keep up the good work, you are helping to keep this forum alive.

If/When they turn the lights out here, not sure if I would post much at other Corvette sites. Probably just lurk a bit.

Sounds like there is a good story behind some of your comments above. I always gave my ideas at work freely, until one day when someone asked for input, I wrote it up as a patent submission. Ended up getting a few ( company property). You’d be surprised at what people do.

SuperBuickGuy · Oct 17, 2018

rtj said:
Keep up the good work, you are helping to keep this forum alive.

If/When they turn the lights out here, not sure if I would post much at other Corvette sites. Probably just lurk a bit.

Sounds like there is a good story behind some of your comments above. I always gave my ideas at work freely, until one day when someone asked for input, I wrote it up as a patent submission. Ended up getting a few ( company property). You’d be surprised at what people do.

it was a rocky start here, but I like the knowledge base so I keep posting.

BBShark · Oct 18, 2018

rtj said:
Keep up the good work, you are helping to keep this forum alive.

If/When they turn the lights out here, not sure if I would post much at other Corvette sites. Probably just lurk a bit.

Sounds like there is a good story behind some of your comments above. I always gave my ideas at work freely, until one day when someone asked for input, I wrote it up as a patent submission. Ended up getting a few ( company property). You’d be surprised at what people do.

The lights won't go out here for the foreseeable future. If VetteMod can serve as an archive for build threads like this, I think it has a valuable purpose. Personally, I use this site as a resource for information, kind of an automotive Wikipedia. Also, I have a ton of pictures hosted here.

rtj · Oct 18, 2018

BBShark said:
The lights won't go out here for the foreseeable future. If VetteMod can serve as an archive for build threads like this, I think it has a valuable purpose. Personally, I use this site as a resource for information, kind of an automotive Wikipedia. Also, I have a ton of pictures hosted here.

:thumbs:

Red77 · Oct 18, 2018

I mostly lurk on the other sites lest I stir up the wrath of the "experts" there. I like looking at builds for ideas, learning fixes for my own issues, and occasionally if I have something of use I chime in. I chime in here because these kind of builds really get my blood pumping. I don't have much time or $$$ for my project at the moment, so this is all part of the research and motivation phase of my build.

This thread is BIG on the motivation, thank you SBG for that. :1st:

SuperBuickGuy · Oct 19, 2018

critical dimensions

onward
starting to trial fit

good grief there are a lot of layers.... still wonder if it'd been better to just get a front-cut and weld it to the rails... probably would, but since when do I do things the easy way?

for those doing this - the plane of the edge of the cradle is the inner point of the upper control arms - the actual dimension is (and I may have to correct this) 37 1/4 from bolt face to bolt face... the cradle is 36 1/2 and you need 3/8" per side to clear the inner portion of the upper control arm... the arm itself is 13 1/2 front and 12 3/4 rear above the lower control arm bolts and the rear most arm is 3 3/8 forward of the rear most, lower-control arm edge flange (outside).

that - with 2" flares, is 3 1/4 inedited

note how the center line is in the middle of the hub but the upper and lower control arms aren't...

hopefully Sunday I'll get a chance to make all that permanent

I enjoy adding to the knowledge base - and best of all, if I can get someone to say "well hell, if you can do it, so can I" that is winning to me.... I grew up around a lot of people who told me what was impossible :3rd: