Search results for query: *

Has anyone used one? Are they worth the time and money? I will be installing it on my 383 stroker. I have a mild cam, holly 4160, with an MSD Ready to Run distributor.

Can I use 3/8 fuel hose from the manifold to the booster? If not any suggestions? Thank you, Jack, Happy Easter!

I purchased a set of glass t-tops for my 77. I have heard that weather strips are different than the OE tops. Has anyone rebuilt a set and done it for a 77 or older model. What weather strips did you use and what mods did you have to make to the locking mechanism compatable with an older...

I switched carbs on my 77 383 stroker. I bagged the edelbrock and went with a holly 4160. The oem throttle linkage was connected to the edelbrock by puttling the hole at the end of throttle cable over a peg and then using a cotter pin to hold it in place. The holly has a ball connection. I...

I have eliminated my ac with a delete panel etc. I still have the blower but don't know what to do with the resistor. Can it just be wired without the resistor? I really don't think I will ever use it as the car is a summer vehicle. Any thoughts? Thanks, Jack

ok, only in the planning stage, but I'm making plans for my parts car. Engine will be rebuilt and in that though thinking about one of these: http://www.summitracing.com/parts/edl-1553/overview/make/chevrolet/year/1977/model/corvette Any thoughts? Thanks, Jack

I think I saw it some where here, but cant find it. I want to replace my steering rag joint with a better alternative. Is there a universal joint that I can use?

Just pulled the engine and getting the replacement ready. I have a holley 4160 with duel feed and AN and braided from the pump to the carb. Do you see a problem with mounting a fuel filter in the back by the tank splicing the filter in the rubber lines from the tank to the hard line on the...

rplaceing my L48 with a 383, miild but not stock cam, holley 750CFM, edelbrock performer manifold with hooker headers and side pipes. I do want to keep the mechanical pump. BTW, what to do with the vapor return?

does anyone know the size of the hoses that go from the transmission cooling lines to the radiator. Mine seem loose and really have to crank on the clamp. I am not comfortable doing that. Thanks Jack

On one of the hot days here in the Burg, I was driving my 77 on the interstate and lost my th350. It had a weak 1st but 2 and 3 were gone. I have been using synthetic trans fluid and it did not smell burned. At first I thought I may have fried it because of the 373 gears in the rear end...

Got home after a long ride in my 77. The car sat for several hours and then, no start. They battery is good and it appears to be the starter. I am going to remove it and check the circuit but I think the headers cooked the starter. If my suspicions are right what do you recommend for a...

Do you guys have any recommendations for finishing puddy on an SMC car? Or doesn't that matter? Thanks, Jack

I am wondering if will be difficult to cut, remove, etc., the fiberglass skin out of a removeable T-top and relace it with a piece of polycarbonate. I got a set of poly t-tops but they are incredibly flimsy. Any thoughts? Thanks Jack

I am sick of trying to fit air cleaner, carb, and related junk under my stock hood. Thinking about going with an L88 style hood and looking at Ecklers, ACI, ect. Has anyone done this or have any suggestions on venders, installation, or problems with this kind of swap...

I think I have a problem with my Edelbrock carb when the car is run that shut down for a short period of time. I purchased an insulator ( http://www.summitracing.com/parts/EDL-9265/ ) that goes between the carb and manifold. My question is do you think I need a gasket on either side or is...

My A/C is not working so I guess it is time to try a fix. I realize the refrigerant is no longe available. Is a conversion difficult? Are there kits that are better than another? What kind of special tools will I need? Any suggestions? Thanks, Jack

I am thinking about replacing my outside mirrors (sport) which are remote with chrome standard mirrors (not remote). Has anyone done this and are the mounting holes in the door the same? Will I have a set of holes that have to be filled. I just like the looks of the standard mirrors. Any...

tool my old windshield out and going to por15 the bird cage. I plan to use new glass. What do you guys recommend for a bond? I was thinking about this stuff http://www.autobodytoolmart.com/3m-windo-weld-super-fast-08609-p-11376.aspx. Is this all I need? BTW, Happy New Year to all. Jack

I purchased a pair from Vette Brakes and Products, http://www.vbandp.com/C2-C3-Corvettes/C2-C3-Suspension-Products/C3-Rear-End-Chassis/1963-79-Crossmember-Reinforcing-Kit.html. I began think (very dangerous thing to do) since they are aluminum and the cross member is steel wont it develope a...