1958 MGA Coupe

Maybe a low speed ceiling fan up top with some pool noodle blades to make it look ready for lift off... Looking great!
 
thanks

bedliner paint for the cockpit area and seam sealer even make my seams look presentable. then the bedliner paint got white top coat.

bell496.jpg
bell497.jpg
bell498.jpg
bell499.jpg
bell500.jpg
 
and done....battery added along with solar panel for charging, will do some final clean up on paint after it has a few more days of drying time

maybe $200 pipe, $50 gauges, $10 lights, $200 16 ga steel, $40 paint
$10 for 5 or 6 cutoff wheels, $15 5lbs of welding rod, $14 seam sealer, $10 2-3 flap wheels.
$42 battery and solar charger

bell501.jpg
bell502.jpg
bell503.jpg
 
Last edited:
all right time to get back to work, the tube bumper i made with rotating attachment arms to get the postion right but i think i am going to tack weld them on the car so they dont move.....what can possibly go wrong with that strategy?

so after much deliberation i found the horizontal line to measure off of and leveled the tube bumper

IMG_4215.jpg

IMG_4219.jpg
IMG_4217.jpg


then it was no guts no glory and time to tig weld the adjustable brackets in place

IMG_4220.jpg

then it was time to take it make the welds a bit more real and grind off the adjustable part of the bracket and weld it up


IMG_4222.jpg
IMG_4221_(1).jpg
IMG_4223.jpg
 
Last edited:
thanks, i still have to be the worst tig welder ever.....so yesterday i made a new rule......that you should wear the leather welding sleeves ( like cut off shirt sleeves) when TIG welding in a t shirt and leaning on the metal table that you have your work piece on...

yikes when you lose focus and spatial awarness of a moment and the tungsten arcs to the filler rod instead of the work piece and your nice moist arm flesh is leaning on the metal table that the work piece is clamped to you get a little reminder that leather gloves alone are not quite enough.

i remember watching a car show with a guy welding exhaust pipes and he was getting bitten as he got into funny positions. I am happy to say today there were no repeat reminders of not focusing on the tungsten torch.
 
well the helicopter is getting used!!

05022021.5..jpg


now back to the MGA

Honestly I did not fully appreciate how clean the TIG welds are and now much less grinding is needed with them. I try to have only one project at a time going on and I need to fix the door latch mechanism so I can drive the car.....having a bungi cord across my chest is just not the best soloution. So I need to wrap the tube bumper up so i can get to that.


todays chore, clean up the welds, user some filler, sand, prime and paint. i decided to use fiber glass for the task. I like it because its sticky as heck and i think its less susceptible to moisture seeping in. i use the clean sheets for mixing the filler, you dont have to worry about any thing being picked up like if you usecard board.

05022021.3.jpg


05022021.2.jpg

05022021.1.jpg
05022021.4.jpg
 
Looks good.

What is the latch problem?

the star wheel that is on the door that turns and latches on to a cog on the body shut face pillar is no longer parallel and tight and it wobbles which disconnects from the internal parts that allows it to rotate and then hold the door in place.

door_star1.jpg

door_star2.jpg

door_star3.jpg
 
Last edited:
I got a bad “sunburn” on my neck and shoulders when I started tig welding and welded a long time. Now I almost always wear a jacket and gloves. If you don’t have a leather “Bib” on your helmet, adding one helps reflections and keeps the neck from getting burned. I used bulldog clips to attach it.

Mines just square leather, but I might upgrade to one of these : Black Stallion FR Wrap Around Welding Helmet Bib AH2140-NS
 
Last edited:
Looks good.

What is the latch problem?

the star wheel that is on the door that turns and latches on to a cog on the body shut face pillar is no longer parallel and tight and it wobbles which disconnects from the internal parts that allows it to rotate and then hold the door in place.

That is interesting. So it's like a pinion gear that "latches" onto a tooth on the door jamb?
 
That is interesting. So it's like a pinion gear that "latches" onto a tooth on the door jamb?

admittedly i am way over my head on this one, but thats not unusual for me. I am not sure how i am going to pull the repair off but heres the write up, buit you can see the internal star gear if its wobbly can walk off the internal cams

http://mgaguru.com/mgtech/coupe/cp113e.htm

lucky for me the guy who wrote this has offered to help walk me through the process.

latch_4.jpg
latch_4_(1).jpg
latch_2.jpg
latch_2_(1).jpg
 

Latest posts

Back
Top