Recent content by voodoovette

A pair of beautifully machined bells for the dana 44 IRS 30 spline axle. These are made in the USA from 4130 billit steel and have never been used. New they cost $600 for the pair, I'm selling this set for $298.00 on E-Bay. These would be perfect for a rear suspension mod. Selling because I went...

I am in need of the centerline measurements between the front lower control arms piviot/mounting shafts. Is it 16.125" or 16.250"??:confused2:

If you look at the attached PIC's closely, you will notice the factory fastener holes are not drilled in the center of the bracket for the lower control arm bracket. The control arm mount bracket is at an angle in relation to the frame bracket. This is factory original and only on the pass side...

I picked up a frame from a 74 vette, very clean, no rust. The driver side lower control arm mount was damaged, moved over about .250". I corrected this by replacing the mount but after a lot of measuring have noticed the drivers side front crossmember, upper and lower control arm mounts raised...

Hello, If anyone has an old idler arm sitting around, I am looking for a measurement of the amount of offset there is made into the frame mounting portion of the idler arm assembly. To attempt to clarify, if you took the idler arm mounting flange with the two bolt holes for the frame and placed...

I am reaching out to find someone who has modified C-3 corvette lower or upper control arms to install spherical bearings. I see Duntov Motors sells the complete sets for a big penny. I would like to do my own and am researching the process. Looking for some input from someone who has hands on...

I am looking for all of your opinions of which would be the best way to go for track and some street. Please let me know what your preference would be, option 1 or 2. I am not concerned about race rules, it is just club racing for fun. 1) Borgeson 12/1 ratio power box, billet and roller...

I have for sale a Dana Super 44 differential removed from a 2003 viper. It comes with a pair on brand new, 4130 Amreican made 930 bells. The bells alone cost $600 for the pair. The differential is low milage and in great shape. Gear ratio is 3.08. I am asking $400.00 plus actual shipping cost...

I am looking for the length of a 73 Vette idler arm from center line of mount piviot to center line of tapered stud for center link. Also want to confirm that it has a 1" drop. I do not have my original and just need the measurements for billet unit. I know Duntov sells these but the price of...

I am in need of the rear trailing arm measurement from center line of front pivot point to center line of spindle hub. I need it to be accurate, I do not have my original ones, sold. Building custom rear suspension and need measurement for locating new hub. Body is off frame, so I cannot locate...

I sent out a sample for testing of the spray on coating that the factory applied to the interior of my 1973 corvette. The results came back today, stating the coating is a tar base that contains 2% Chrysotile Asbestos. If you are doing repairs to the interior floor of your vette, be carefull...

Anyone know what the spray on coating that was factory applied to the interior floor pan of my 73 vette is? whats in it and what is the best way to remove it?:confused:

I agree with TT, I have run solid mounts is several cars and the vibration or added noise was minimal. Now if you had a Bently or RR then this would not be a good choice, but it is a corvette:shocking: that was made for performance. Not all solid mounts are the same, Moroso makes them in two...

pinion offset BBshark, you mentioned the pinion is offset .5", is this a virtical measurement, because the half shafts are the same length and I need to know if I am missing something. My pinion is currently centered in the chassis with the engine/trans offset 1" to the right/pass side with a...

Spline count This is just a quick basic answer, but if all being equil, the shaft with more splines and if using involute spline type will be stronger because of more spline surface area. An involute spline is tapered, being wider at the bottom or base and narrower at the top, triangle shape...