General Information
This is my 1977 Corvette Pro touring.
Here's a list of specifications & modifications:
Body:
- L88 flares
- Standox MonteCarlo Magic effect paint
- Custom Headlights using 90mm Hella Modules & fabricated aluminium buckets
Interior
- Autometer Ultra Lite Gauges
- Custom fabricated center console & shifter plate
- Lokar shift indicator boot
- Backlit power window switches
Engine
- 355 CID SBC 4 bolt mains
- Flat top pistons
- Aluminium L98 D-port heads with screw in studs, guideplates and comp cams roller tip rockers (1:1.6)
- ZZ Intake manifold
- Edelbrock Performer Carb modified for AN connection on front vac. port
- DeboTech carbon Fiber 16" aircleaner housing
- KRC serpentine drive system with KRC power steering pump, water pump and reservoir.
- Fabricated center bolt covers
- Mallory Magnetic Breakerless Ignition distributor converted to crab cap
- Fabricated stainless steel thermostat housing
- CSI billet aluminium throttle bracket
- Milodon Gear Drive
- Milodon 7qt oil pan
- Hooker side exhaust headers
- McLeod gear reduction mini starter
- Powermaster mini alternator
- Earls billet PVC
- Heat protective spark plug boots
- MSD 8.5mm spark plug wires
- Mallory HyFire VI ignition box
- Mallory ProMaster ignition coil
- CV Products oil thermostat
- Moroso Sandwich Adapter
- -12 AN plumbed cooler lines
- Barnes -12 AN mech. temp gauge port
Chassis, Suspension & Steering
- Custom fabricated speader bar
- Custom fabricated rear coil over suspension with Aldan Eagle adjustable shocks
- Custom aluminium tie rods with rod ends
- Custom square plates for locking strut rod bolts
- Dropped front suspension with bilstein shocks, cut 550lbs springs and custom polyurethane spring cushions
- All rebuilt & blueprinted steering linkage.
- Custom lines & plumbing on steering control valve.
- Mocal Powersteering fluid cooler
- VB&P rear crossmember bushing support plates
- Custom trailing arms for coil over shocks
- Polyurethane front suspension bushings
- Polyurethane front & rear sway bar bushings
- Added rear sway bar (because of coil over shocks)
- Polyurethena Engine mounts
- Polyurethane Pinion bushing with stainless steel bolt/nut
Transmission
- Rebuilt & beefed up TH350
- Hughes performance deep oil pan
- Transmission temp probe
- AN plumbed cooler lines
- Mocal Transmission cooler
- VDO Vehicle Speed Sensor
Wheels, Tires & Brakes
- Intro Pentia soft lip 18x10 & 18x11 wheels with Nitto 555R tires
- Rebuilt/stainless sleeved stock calipers, epoxy painted gold
- C5 1" bore master cylinder with fluid level warning switch
- Stainless steel rear caliper lines
- Russel stainless steel braided flex lines
Miscellaneous
- HotRodAir heater
- American Graffity AC delete heater box
- Custom fabricated aluminium vacuum reservoir
- All heater lines plumbed with AN hardware
- Spal 16" electric fan, relay switched
- Relay switched Xenon headlights
- LED bulbs everywhere.
Here's a list of specifications & modifications:
Body:
- L88 flares
- Standox MonteCarlo Magic effect paint
- Custom Headlights using 90mm Hella Modules & fabricated aluminium buckets
Interior
- Autometer Ultra Lite Gauges
- Custom fabricated center console & shifter plate
- Lokar shift indicator boot
- Backlit power window switches
Engine
- 355 CID SBC 4 bolt mains
- Flat top pistons
- Aluminium L98 D-port heads with screw in studs, guideplates and comp cams roller tip rockers (1:1.6)
- ZZ Intake manifold
- Edelbrock Performer Carb modified for AN connection on front vac. port
- DeboTech carbon Fiber 16" aircleaner housing
- KRC serpentine drive system with KRC power steering pump, water pump and reservoir.
- Fabricated center bolt covers
- Mallory Magnetic Breakerless Ignition distributor converted to crab cap
- Fabricated stainless steel thermostat housing
- CSI billet aluminium throttle bracket
- Milodon Gear Drive
- Milodon 7qt oil pan
- Hooker side exhaust headers
- McLeod gear reduction mini starter
- Powermaster mini alternator
- Earls billet PVC
- Heat protective spark plug boots
- MSD 8.5mm spark plug wires
- Mallory HyFire VI ignition box
- Mallory ProMaster ignition coil
- CV Products oil thermostat
- Moroso Sandwich Adapter
- -12 AN plumbed cooler lines
- Barnes -12 AN mech. temp gauge port
Chassis, Suspension & Steering
- Custom fabricated speader bar
- Custom fabricated rear coil over suspension with Aldan Eagle adjustable shocks
- Custom aluminium tie rods with rod ends
- Custom square plates for locking strut rod bolts
- Dropped front suspension with bilstein shocks, cut 550lbs springs and custom polyurethane spring cushions
- All rebuilt & blueprinted steering linkage.
- Custom lines & plumbing on steering control valve.
- Mocal Powersteering fluid cooler
- VB&P rear crossmember bushing support plates
- Custom trailing arms for coil over shocks
- Polyurethane front suspension bushings
- Polyurethane front & rear sway bar bushings
- Added rear sway bar (because of coil over shocks)
- Polyurethena Engine mounts
- Polyurethane Pinion bushing with stainless steel bolt/nut
Transmission
- Rebuilt & beefed up TH350
- Hughes performance deep oil pan
- Transmission temp probe
- AN plumbed cooler lines
- Mocal Transmission cooler
- VDO Vehicle Speed Sensor
Wheels, Tires & Brakes
- Intro Pentia soft lip 18x10 & 18x11 wheels with Nitto 555R tires
- Rebuilt/stainless sleeved stock calipers, epoxy painted gold
- C5 1" bore master cylinder with fluid level warning switch
- Stainless steel rear caliper lines
- Russel stainless steel braided flex lines
Miscellaneous
- HotRodAir heater
- American Graffity AC delete heater box
- Custom fabricated aluminium vacuum reservoir
- All heater lines plumbed with AN hardware
- Spal 16" electric fan, relay switched
- Relay switched Xenon headlights
- LED bulbs everywhere.
